Engineering • rebuilding • vehicle service
When the repair requires more than replacing a part, GTE Engineering goes deeper. We diagnose complete systems, rebuild sophisticated components, balance clutch assemblies in-house and develop solutions for exclusive vehicles—from a single actuator to a complete transmission, engine project or hard-to-source component.
Our workshop supports owners, collectors and professional repair facilities working with Ferrari, Lamborghini, Maserati, Aston Martin, McLaren, Audi R8 and other select performance vehicles. Whether your car comes to our workshop or a removed component is sent to us, the work begins with understanding the application and the problem.
Our capabilities
From the vehicle to the smallest component.
Explore the systems and services behind the GTE Engineering name.
Transmission & gearbox rebuilding
Inspection and rebuilding for select dual-clutch, automated-manual and manual transmission applications.
- Getrag / Magna 7DCL750 transmission service and rebuilding
- Selected Graziano gearboxes, including Ferrari and Maserati applications and McLaren DCT
- Inspection of gears, shafts, bearings, synchronizers, housings and related components
- Electronic, hydraulic and clutch-control work where required by the unit and approved scope
- Assembly, setup and applicable calibration
F1, E-Gear, ASM & hydraulic systems
Component-level service for the systems that select gears and operate the clutch.
- Ferrari F1 actuators and hydraulic power units
- Lamborghini E-Gear actuators and hydraulic systems
- Maserati Cambiocorsa and DuoSelect systems
- Aston Martin Sportshift (ASM) components
- Applicable pumps, accumulators, solenoids, hoses and sensors
- System diagnosis, bleeding, setup and calibration when the vehicle is serviced at GTE
PEGA Clutch® & flywheel services
Clutch rebuilding and application-specific friction solutions for road and performance use.
- Clutch disc and pressure-plate rebuilding for supported applications
- Organic, Kevlar® and ceramic friction options where applicable
- Flywheel inspection, resurfacing and balancing services
- Clutch and flywheel balancing and related release components
- Custom configurations for special applications, subject to assessment
Engine service & restoration
Workshop support for engine concerns, from investigation through larger restoration projects.
- Mechanical inspection and fault diagnosis
- Engine repair, restoration and overhaul projects
- Related cooling-system and water-pump rebuild services
- Parts and additional work assessed to suit the engine and its condition
Driveline, PTU & supporting components
Specialist rebuilding extends beyond the transmission itself.
- Ferrari FF and applicable GTC4Lusso 4RM power transfer units and related hydraulic power units
- Selected Lamborghini viscous couplings
- Clutch release bearings and hydraulic release components
- Water pumps, hydraulic hoses and other cataloged assemblies
Diagnostics, electronics & commissioning
A fault code is a starting point. We investigate how the mechanical, hydraulic and electronic systems work together.
- Vehicle fault-code analysis and system diagnosis
- Electrical, sensor and hydraulic-system assessment
- Supported control-system programming and software services
- System bleeding, clutch and transmission setup, adaptations and calibration as applicable
- Technical support and service documentation for owners and professional installers
In-house precision equipment
Clutch & rotating-component balancing.
GTE performs clutch and flywheel balancing in-house using our MBS Balans V-IVB 100 vertical balancing machine. Proper balancing depends on more than equipment: the mounting datum, dedicated tooling, component condition and correction method all matter.
We also welcome balancing inquiries from workshops, manufacturers and other businesses for suitable rotating components. Send us the part details and requirements so we can assess the mounting, tooling and scope before accepting the work.
Engineering beyond the catalog
Reverse engineering & custom parts development.
Some projects start with a part that is unavailable, a requirement that off-the-shelf solutions do not meet, or an exclusive vehicle that deserves a carefully considered approach. GTE works with clients to assess the original component and develop application-specific solutions.
- Reverse engineering and dimensional assessment of existing components
- Replacement-part feasibility, parts development and manufacturing projects
- Custom clutch friction and performance solutions for unique applications
- Application-specific components and projects for collectors, specialists and exclusive clients
Example: Ferrari F50 clutch lining
Our Ferrari F50 clutch lining project illustrates the kind of specialized development we can undertake when a rare application calls for a tailored solution.
Development begins with an assessment of the component, intended use and technical requirements. Feasibility, specifications, testing and scope are agreed for each project.
See our work
Experience backed by real projects.
Explore workshop projects and technical guides to see how we approach diagnosis, component repair and the details behind the finished work.
Start with the right information
How can we help?
Tell us the vehicle, year and VIN when applicable, the component and part number, symptoms, fault codes and any previous work. Photographs and diagnostic reports can help us understand your request.
Bringing the vehicle? Request a workshop appointment. Sending a component or discussing a development project? Request a quote before shipping.
Applications, repair scope, parts, availability, pricing and turnaround are confirmed for each vehicle or component and the approved estimate.