Flywheel Service

A precision flywheel service starts with knowing how much metal to leave in place. GTE Engineering has completed thousands of exotic-car component rebuilds and offers rebuild services for more than 50 products. This guide takes you inside our workshop to show how we inspect the part, set up the grinder, measure what comes off and verify the finished surface.

1. Inspect and grind the friction face

We center the flywheel on our Italian-built COMEC grinder. The rotary table carries the friction track beneath the grinding stone. The technician selects the abrasive for the flywheel material, sets the feed and directs coolant to the contact area. A fine cut depends on the setup: how the part is supported and centered, how the stone is prepared and how the technician controls each pass. We inspect the friction face and confirm that the part is suitable for resurfacing before removing metal.

Italian COMEC flywheel grinder with its vertical head above the rotary table.
The COMEC grinder and its rotary table.
Grinding stone and coolant at the flywheel friction track.
The stone meets the friction track under coolant.

2. Measure how much came off

On the Lamborghini flywheel shown here, the gauge read 12.67 mm before grinding and 12.60 mm afterward. We removed 0.07 mm (70 µm). On the Lamborghini flywheels we service, cuts are often around 0.10 mm (100 µm) or less, where the part and its dimensions permit. The condition and specification of each part determine what can be removed.

Cut depth in perspective: A 1.00 mm (1,000 µm) cut is ten times as deep as a 0.10 mm (100 µm) cut. This is a scale comparison, not a machining target or an allowable limit.

Before resurfacing, the GTE workshop gauge reads 12.67 mm.
Before resurfacing · 12.67 mm
After resurfacing, the GTE workshop gauge reads 12.60 mm.
After resurfacing · 12.60 mm

3. Compare four points on the finished face

An even friction track helps the lining seat across its width. The four photographed heights spanned 0.03 mm (30 µm). To check for curvature across the whole track, compare inner and outer readings at several positions around the flywheel using a common zero.

Point A on the finished friction face, with a gauge reading of 0.00 mm.
Point A · 0.00 mm
Point B on the finished friction face, with a gauge reading of 0.00 mm.
Point B · 0.00 mm
Point C on the finished friction face, with a gauge reading of −0.03 mm.
Point C · −0.03 mm
Point D on the finished friction face, with a gauge reading of −0.01 mm.
Point D · −0.01 mm

The 70 µm removed and the 30 µm span between the four finished-face readings describe different things. The first is the before-and-after change at the measurement reference. The second compares local heights after grinding. We keep those measurements separate when checking the finished geometry.

Why a light cut matters to clutch setup

The position of the friction face relative to the pressure-plate mounting surface is part of the clutch’s working geometry. Removing more material than necessary can change that relationship and use up adjustment margin. On systems that allow technician adjustment, the Point of Initial Slip (PIS) can be set within the range specified for that application. On applicable Aston Martin SportShift ASM systems, the controller learns the clutch engagement point and the technician runs and verifies the prescribed procedure. Neither approach replaces correct mechanical dimensions.

Technical references: GTE technical bulletins on clutch calibration · Aston Martin SportShift service bulletin SB-07-0315V4.

4. Optional bench balancing

GTE offers bench balancing after resurfacing for an additional charge. The balance report identifies the component tested and records the result. Page 6 of the PDF shows a sample report. Read the clutch and flywheel balancing guide.

5. Final quality control

Before return, we review the finished friction track and the dimensions required for that part. The before-and-after measurements tell us how much metal was removed; readings taken across the finished track check the surface. When bench balancing was ordered, we also review the recorded balance result.

6. Surface profile and bench testing

Unloaded surface height

The four gauge readings ranged from 0.00 to −0.03 mm. The depth of the lowest reading tells us how far that point sat below the gauge zero. To determine the width of a low area or how far it continues around the ring, measurements are needed between those points.

A broad illustrative band on the annulus fades from light green at −0.03 mm to dark blue at the 0.00 mm datum. An adjacent section magnifies the depth.
Figure 13a. The band illustrates one possible surface profile before clamping. Its width and angular position are schematic.

How we check local contact with pressure-sensitive film

GTE placed short strips of pressure-sensitive film at four areas of the lining interface, bolted down the pressure plate and held the assembly for about five minutes at room temperature. After removing the plate, the workshop inspected the transfer. GTE reported visible contact with no visible gaps in each of the four checked areas. The sectors between the strips were outside the test.

Grooved Lamborghini Aventador PEGA Clutch performance lining with alternating holes on a dark blue GTE Engineering background.
Lamborghini Aventador · PEGA Clutch® Performance Lining FX4C-SC.
Four short pieces of film labelled A–D cross sections of the friction track. The other sectors appear grey.
Figure 13b. The Aventador lining supplies the geometry for this illustration. Pink represents example transfer on the film strips. Their positions are schematic and the colour has no numerical pressure scale.

Conclusion

Measure first, remove only what the part requires, and verify the finished geometry before release. This is how GTE preserves the dimensions that matter to clutch setup. It takes precise tooling, careful measurement and the judgment to know when to stop cutting.

Test method reference: Fujifilm on pressure-sensitive film.

Open printable PDF Download PDF

9 pages · US Letter. Select Print in your PDF viewer or share menu.