← Back to Workshop Projects

GTE Engineering / Workshop projects

Ferrari 360 Modena Graziano Transmission Rebuild

Grinding noises, gears jumping out, and difficult reverse selection led to a complete teardown—and a severely damaged main support bearing.

Ferrari 360 Modena Graziano transmission rebuild by GTE Engineering, side view
Vehicle
Ferrari 360 Modena
Transmission
Graziano gearbox
Work performed
Complete teardown & rebuild
Completed
Calibrated, tested & returned

The challenge

Grinding. Gear disengagement. Difficult reverse.

Ferrari 360 Modena Graziano transmission housing and shaft during disassembly at GTE Engineering
Upright transmission housing at the start of teardown.
Dismantled Ferrari 360 transmission case with its removed housing section during the GTE Engineering rebuild
Open transmission case and removed housing section.

This Ferrari 360 Modena transmission arrived with a grinding sound and a tendency to jump out of gear. The customer also reported shifting difficulties, particularly when selecting reverse.

The unit required complete disassembly so we could inspect the internal components and establish the extent of the damage.

The findings

A main support bearing had disintegrated.

Close-up of a severely damaged Ferrari 360 Graziano transmission bearing with disintegrated material and visible rollers
The disintegrated support bearing found during teardown.
Ferrari 360 Graziano transmission synchronizer ring, sliding sleeve, selector fork, and gear assembly laid out at GTE Engineering
Synchronizer components, selector fork, and gear assembly.

With the Graziano transmission completely apart, we found that the main support bearing had disintegrated. Other internal components, bearings, and bushings were also severely damaged.

The teardown photographs document the failed bearing and affected components before rebuilding. The damage shown is from this unit.

Technical information

What the Graziano teardown revealed.

The teardown let us compare the driver’s shifting complaints with the condition of the bearings, synchronizers and bushings.

Area Finding
Gear selection Grinding, gears jumping out and difficulty selecting reverse.
Main support bearing The main support bearing had disintegrated.
Synchronizers and bushings The rebuild required new OEM synchronizers and bushings.
Bearing upgrade A high-performance replacement bearing was selected for the rebuild.

The work

The bearing upgrade

Better support for the rebuild.

Destroyed Ferrari 360 transmission bearing held beside the replacement bearing, both highlighted with red arrows at GTE Engineering
Failed bearing on the left and its replacement on the right.
GTE Engineering Ferrari 360 transmission housing and shaft with a red arrow identifying the replacement support bearing
Replacement support bearing highlighted by the red arrow.
Ferrari 360 transmission support bearing installed around the shaft in the housing at GTE Engineering
Support bearing and shaft in the transmission housing.

We fitted high-performance replacement bearings, selected to improve load support and long-term durability. The red arrows in the photographs highlight the bearing components discussed in this project.

The comparison photograph shows the destroyed bearing beside its replacement, making the extent of the original failure clear.

The work

New OEM synchronizers and bushings.

Ferrari 360 Graziano transmission gears and synchronizer assembly with a red arrow during the GTE rebuild
Gear and synchronizer assembly detail.
GTE Engineering Ferrari 360 Graziano internal gear, synchronizer and bearing assembly during rebuilding
Internal gear and bearing assembly during reassembly.

Alongside the bearing work, we replaced the synchronizers and bushings with brand-new OEM components. The transmission was then reassembled, recalibrated, and tested before being sent back to the customer.

  1. Complete disassembly and internal inspection
  2. Replacement of damaged bearings with high-performance bearings
  3. Installation of brand-new OEM synchronizers and bushings
  4. Reassembly, recalibration, and final testing

The result

Rebuilt, tested, and sent back.

Completed Ferrari 360 transmission, front three-quarter view
Completed Ferrari 360 transmission, front three-quarter view
Completed Ferrari 360 transmission, bellhousing view
Completed Ferrari 360 transmission, bellhousing view
Completed Ferrari 360 transmission, side view
Completed Ferrari 360 transmission, side view

After the bearing and internal component work, we recalibrated and tested the transmission, then returned the completed unit to the customer.

GTE Engineering has been rebuilding Graziano transmissions for more than 10 years. Each project builds on that experience and careful inspection of the individual unit.

Workshop photos have been retouched for presentation.

← Back to Workshop Projects